his is the LIDAR Lite, a compact high
performance optical distance measurement sensor
from PulsedLight. The LIDAR Lite is ideal when used
in drone, robot, or unmanned vehicle situations where
you need a reliable and powerful proximity sensor but
don’t possess a lot of space.
Store Pickup Available!
Description: This is the LIDAR Lite, a compact high performance optical distance measurement
sensor from PulsedLight. The LIDAR Lite is ideal when used in drone, robot, or unmanned
vehicle situations where you need a reliable and powerful proximity sensor but don’t possess a
lot of space. All you need to communicate with this sensor is a standard I2C or PWM interface
and the LIDAR Lite, with its range of up to 40 meters, will be yours to command!
Each LIDAR Lite features an edge emitting, 905nm (75um, 1 watt, 4 mrad, 14mm optic), single
stripe laser transmitter and a surface mount PIN, 3° FOV with 14mm optics receiver. The LIDAR
Lite operates between 4.7 - 5.5VDC with a max of 6V DC and has a current consumption rate
of <100mA at continuous operation. On top of everything else, the LIDAR Lite has an acquisition
time of only 0.02 seconds or less and can be interfaced via I2C or PWM.
Note: The LIDAR Lite is designated as Class 1 during all procedures of operation, however operating
the sensor without its optics or housing or making modifications to the housing can result in direct
exposure to laser radiation and the risk of permanent eye damage. Direct eye contact should be
avoided and under no circumstances should you ever stare straight into the emitter.
Range: 0-40m Laser Emitter
Accuracy: +/- 0.025m
Power: 4.7 - 5.5V DC Nominal, Maximum 6V DC
Current Consumption: <100mA continuous operation
Acquisition Time: < 0.02 sec
Rep Rate: 1-100Hz
Interface: I2C or PWM
01S Vibration Sensor Module vibration Analog Output Sensitivity LM393Size: 41 * 15 * 12.5mm The main chip: LM393, vibrating probe Operating voltage: DC 3-5V Main features: Has a signal output instructions; With analog and TTL-level signal output signal; Output valid signal is high, the light goes out; Adjustable sensitivity (fine-tuning); Vibration...
RCWL-0516 Microwave Radar Sensor Module Human Body Induction Switch Module
Description: Type K Type. Mounting thread: M6 Temperature Range:0-600°C. Thread Diameter:6mm / 0.23". Internal Insulation:Fibreglass. External Shielding:Metal Shield. Total Length:1M / 39". Fork Terminal Spacing: 3.5mm / 0.13". Color: As Picture Shown. 10mm thread sensor for accurate measurement.
Add heat-vision to your project and with an AMG8833 Grid-EYE Breakout! This sensor from Panasonic is an 8x8 array of IR thermal sensors. When connected to your microcontroller (or raspberry Pi) it will return an array of 64 individual infrared temperature readings over I2C. It's like those fancy thermal cameras, but compact and simple enough for easy...
Type: Microwave SensorChip: HB100Frequency: 10.525GHzVoltage: DC 5V±0.25VCurrent: 40mASize: 38 x 45 x 7 mm (L x W x H)Application: Automatic door startup, Car, House intrusion alarm, Collision warningTraffic monitoringNote:Please pay attention to the Voltage/Current/Power of your own devices.To ensure product safety, check whether this item is compliant...
FPM10A Optical Fingerprint Reader Sensor Modules Connect RoboticsBD Fingerprint Shield on top the Arduino Uno R3 Install Adafruit Fingerprint Library (Check Download Tab) Upload this code to Arduino Uno Board (Arduino Code SFG Demo) Run SFG Demo V2.0 Windows Test Software as Administrator
V3 Kit Voice Recognition Module BoardFor Arduino Compatible Sensor Voice Recognition Module is a compact and easy-control speaking recognition board.This product is a speaker-dependent voice recognition module. It supports up to 80 voice commands in all. Max 7 voice commands could work at the same time. Sample Code & Library and Manual is available...
2.8V Regulator - Provides the required 2.8V for the sensor I2C Level Shifter - Provides logic level conversion from 2.8V to VCC 3-in-1 Module IR Emitter Range Sensor Ambient Light Sensor Measures absolute range up to 10cm Gesture Recognition I2C Interface Two Programmable GPIO Sharp Sensor Board Layout
Angle Sensor Module for Arduino High-sensitivity angle sensor SW-520D Comparator output, clean signal, great waveform, strong driving ability, more than 15mA Distribution positioner sensitivity adjustment Working voltage: 3.3V~12V Output form: Digital switching output (0 and 1) With fixed bolt hole for easy installation
Chip: BH1750FVI Power Supply: 3.3V - 5V Light Range：0 - 65535 lx(Lux) Sensor Built-in: 16 bit AD converter Size(L x W): Approx. 3.2cm x 1.5cm Direct digital output, bypassing the complex calculation, bypassing the calibration Close to the spectral characteristics of visual Widely used to 1-lux high precision measurement Standard NXP IIC communication...
HX1838 NEC Code Infrared Remote Control Module DIY Kit
The Leap Motion Controller tracks both hands and all 10 fingers with pinpoint precision and incredible speed. Setup is easy, just plug into your PC or Mac and launch Airspace, your home for Leap Motion apps. Play, create, and explore in a whole new way!In Airspace, the Leap Motion App store,
The HMC5983 includes our state-of-the-art, high-resolution HMC118X series magnetoresistive sensors plus an ASIC containing amplification, automatic degaussing strap drivers, offset cancellation, and a 12-bit ADC that enables 1° to 2° compass heading accuracy. The I²C or SPI serial bus allows for easy interface.
The FLiR Dev Kit includes a breakout as well as a Lepton® longwave infrared (LWIR) imager. With this kit you will be able to be able to bring FLiR’s thermal imaging reliability and power to your Arduino, Raspberry Pi, or any ARM based development tool all in an easy to access breadboard friendly package. Flir Lepton Installation Instruction 1 Flir Lepton...